Product Details
Heavy duty holesaws for industrial use. The high speed steel M3 bi-metal cutting edge provides long life and the 4/6tpi variable pitch teeth enable fast, easy cutting. Suitable for cutting hardwood, softwood, plywood, laminates, nailed wood, plastics, non-ferrous metals, stainless steel and steel.
Technical Specification
| Brand |
Toolpak |
| Manufacture ID |
HOLE29 |
Delivery details
Please note items delivered by our suppliers are not available for the options above.
Delivery times may vary.
More about Delivery & Returns
Click & Collect details
If you are using our Click & Collect service please note the following:
- Order online or over the phone and collect in branch from 10 minutes later.
- Ensure you check stock is available for collection at your chosen branch.
- Check branch opening hours to ensure you have sufficient time to collect.
- For items not available for same day collection, place order before 8pm Mon-Sat (4pm Sun) and you can collect Next Business Day (Mon-Fri) after 3pm.
- If we have your mobile number, we’ll send you a text when your order is ready to collect.
Reviews
★★★★★
★★★★★
M3 Bi Metal Holesaw 29mm is rated
4.3 out of
5 by
52.
Rated 1 out of
5
by
Anonymous from
Poor quality
It Failed to cut one hole on 1.5mm steel box, used lubricant and slow speed but went blunt before finish.
Credit to Tool Station they gave a refund.
Date published: 2019-03-05
Rated 4 out of
5
by
MatthewTheWriter from
cuts holes
the only problem I have with this is that 2 of the 4 holes don't line up properly with the pins of the fitting that it is mounted on
Date published: 2019-02-20
Rated 4 out of
5
by
9013alanb from
No frills hole saw that does the job
Does what it says on fibreglass and wood which is what I bought it for. Sharp and heavy duty surprisingly good for the price.
Date published: 2019-02-19
Rated 4 out of
5
by
Graeme AB from
Does what is says on the box
Needed to cut a hole for a cable grommet, simple job, easy tool to use.
Date published: 2019-02-19
Rated 4 out of
5
by
MRGF from
simple, single holes.
I purchased this 57mm holesaw, along with the same branded arbor to fit it to.
I found the fitting of the two a little fiddly, despite being the same brand (Purposefully purchased together, just to be sure to fit). They did go after a few tries and seemed just a little slack, once fully tightened. I did only use hand pressure as I did not want the tools to lock together, forever but the looseness may just make hole a little less accurate. I don't think this in itself is a big issue, though, just a gripe.
The other thing was that the saw, although sharp to the touch, seemed quite slow in wood. This might just be typical of wood cutting saws, rather then metal/plastic but I thought the sharpness might dull too quickly for any real use. I cut eight holes in wood that was actually bed slats, that go under the mattress of a slatted bed frame so you can imagine, hard wood but not particularly thick! Add to that, some of the paint flaked off, so the tool will start to rust, if stored poorly. Not an issue if you use it a lot, wear it out and buy a new one but for medium/low usage, make sure you spray oil on it, prior to popping it in its box or your toolbox.
The slats for removing the cooing were a little fiddly, too but I assume with practice, it will pop out easily enough and recon they will be the same or similar, no matter how much you spend on a tool. its a shame I couldn't find the 57mm saw in a set, as I would have then spent more but had a handy set, the arbor or two, along with the important allen key, all in a nice case. However, I could only see a kit with a 51mm (Too small) or a 64mm one and that was far too big.
I could have spent a fortune on a kit that had the correct size but I only needed eight holes, this tome round and may never need to use it again.
So, good for my use, if you want to cut hole all day, every day, spend more, buy better quality!
Date published: 2019-01-22
Rated 5 out of
5
by
zachariah from
Great Item
Cheap and excellent value for money!
Date published: 2018-11-08
Rated 5 out of
5
by
Richard Brown from
40mm Holesaw
It's a 40mm hole saw ! Not much more to add, other than you'll need an arbor to use it if you haven't got one. Only used it to cut through 9mm UPVC soffit, did the job.
Date published: 2018-10-18
Rated 5 out of
5
by
Lumpy from
spot on, fit for purpose
I only needed this to cut a 4" hole in the bathroom ceiling plasterboard layers and it did this perfectly as would be expected. I have no idea how it would work in metal but was perfect for my use.
Date published: 2018-09-19
Sign in
Trolley
This site uses cookies to store information on your computer. Some of these cookies are essential to make the site work and others help us to improve services by giving us some insight into how the site is used. You can view our cookies policy