Selected
Quantity

Add to trolley for...

- Change your branch

Check stock in your local branch

Free Saturday Delivery on orders over £75

Product Details

The only self-drive you can't overtighten. Includes an inner cam that continues to rotate once outer cam reaches maximum torque. Maximum 20kg safe load. Supplied with screws.



Ideal for hanging clocks, picture frames, light switches and light bathroom fittings. Updated self-drive design addresses common issues faced by users. No pilot holes or pre-drilling required.

Technical Specification
Brand GripIt
Pack Size 100
Delivery details
Order value: Under £10 £10 & over
Express usually Next Business Day before 6pm £5 Free
Turbo usually Next Business Day before 12 noon £10 £5
Remote areas standard delivery (2-4 days) £5 Free
Order Value: Under £25 Over £25 but less than £75 £75 & Over
£10 £5 Free


Please note items delivered by our suppliers are not available for the options above. Delivery times may vary.

More about Delivery & Returns
Click & Collect details
If you are using our Click & Collect service please note the following:
  • Order online or over the phone and collect in branch from 5 minutes later.
  • Ensure you check stock is available for collection at your chosen branch.
  • Check branch opening hours to ensure you have sufficient time to collect.
  • For items not available for same day collection, place order before 8pm Mon-Sat (4pm Sun) and you can collect Next Business Day (Mon-Fri) after 3pm.
  • If we have your mobile number, we’ll send you a text when your order is ready to collect.
Reviews
TwistIt Self Drive Plasterboard Fixing Nylon (100 Pack) is rated 1.0 out of 5 by 6.
Rated 1 out of 5 by from Don't Bother Thought these would be great, the inner fitting wears before you can get the fixing in the plasterboard and once broken you cannot get the fitting out, should have bought plain simple rawplugs these are useless
Date published: 2019-10-04
Rated 1 out of 5 by from Rubbish What an absolute waste of time and money. But for the fact it was over 30 days between buying and trying, they would have gone straight back to toolstation for a refund. Absolutely useless piece of kit.
Date published: 2019-04-11
Rated 1 out of 5 by from Stay away!!! Waste of money. Broke 10 before I managed to get one in. Would not buy or dare recommending to anyone
Date published: 2019-04-08
Rated 1 out of 5 by from Not good in any way Double sheet wall. They don’t self drill, even after drilling a large pilot hole the stop half way and strip the screw head. Used 20 to finally get 8 fixings.
Date published: 2018-10-29
Rated 1 out of 5 by from Unusable fittings for plaster board Where to start. I have always used the metal self tapping plaster board fittings but thought I would try these, despite the lurid green insert. However, they do not self tap into plaster board; you will need to pilot drill first. In addition, the feature ratchet cuts in before the insert has fully seated in the plaster board. :-( Thrown them away and bought the more expensive fisher metal inserts instead.
Date published: 2018-10-25
Rated 1 out of 5 by from Not recommended - multiple issues with this item Bought on the strength of the other Gripit products for holding up a lightly loaded shelf. DiY I may be but pretty experienced - 50 years of it in and out of the building trade. Issue 1: the device did not penetrate a plasterboard wall that has been plastered. The plastic point is sharp but does not penetrate well enough for the cutting edges to start to work. Increased pressure causes the device to wobble on the end of the driver (PZ2 bit in drill/driver). Looks like it might be OK in plain unplastered plasterboard. Issue 2: Having manually formed a small hole to start the device so the cutter could work, the built-in clutch was not man enough for the job - plastic chewed up. Possible the finishing plaster was too hard again. Issue 3: Having made the hole a little bigger to get the thread started and changed the device for an undamaged item and using somewhat more pressure, the device bit into the board and the clutch did not release. The device went right through the plasterboard and into the void behind. Gave up here and used a yellow Gripit. There's no information on whether these things can be used on plastered surfaces or only on bare boards. I recommend you save your money and use some other type of fixing - the original Gripits work really well.
Date published: 2018-09-09
  • y_2019, m_12, d_5, h_12
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_6
  • loc_en_GB, sid_88155, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_toolstation-gb
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 44.43ms
  • REVIEWS, PRODUCT

You might also like

This site uses cookies to store information on your computer. Some of these cookies are essential to make the site work and others help us to improve services by giving us some insight into how the site is used. You can view our cookies policy here.