Add to trolley for...

- Change your branch

Check stock in your local branch

Free Saturday Delivery on orders over £75

Product Details

• 5mm segment height. Can be used wet or dry when cutting ceramic tiles.

Technical Specification
Brand Norton
Manufacture ID 70184622956
Bore Size (mm) 25.4
Delivery details
Order value: Under £10 £10 & over
Express usually Next Business Day before 6pm £5 Free
Turbo usually Next Business Day before 12 noon £10 £5
Remote areas standard delivery (2-4 days) £5 Free
Order Value: Under £25 Over £25 but less than £75 £75 & Over
£10 £5 Free

Please note items delivered by our suppliers are not available for the options above. Delivery times may vary.

More about Delivery & Returns
Click & Collect details
If you are using our Click & Collect service please note the following:
  • Order online or over the phone and collect in branch from 5 minutes later.
  • Ensure you check stock is available for collection at your chosen branch.
  • Check branch opening hours to ensure you have sufficient time to collect.
  • For items not available for same day collection, place order before 8pm Mon-Sat (4pm Sun) and you can collect Next Business Day (Mon-Fri) after 3pm.
  • If we have your mobile number, we’ll send you a text when your order is ready to collect.
Norton Tile & Ceramic Cutting Diamond Blade 180 x 25.4mm is rated 4.4 out of 5 by 19.
Rated 3 out of 5 by from Not as good as i hoped it would be I bought this to cut floor tiles but they chipped along the cuts on the 2 tiles I tried it it on. I went back to an old blade which was better and even used a standard tile cutter which gave a better finish. I wouldnt buy another.
Date published: 2019-09-09
Rated 4 out of 5 by from Gets the job done adequately Used this dry in my angle grinder to cut through 8mm thick 330mm square floor tiles. Some chipping, but this is minimised by applying masking tape and cutting through that. In fairness I have yet to find a disk that does not cause some chipping of the cut edge. Perhaps it is just the quality of the glaze these days..... Was able to carefully cut curves and gently work the tile into some required awkward shapes. I actually prefer cutting tiles this way to using my tile cutting machine. I prefer to put up with a bit of dust over getting sprayed with water ! I still get the cleanest results by scoring a tile and snapping it, but that is not always a practical proposition.... Interestingly, I tried cutting a tile with a 115mm diamond segmented disk that I would use to make fine cuts on roof tiles, brick and stone to see what difference it woudl make. There was more chipping of the glaze. The lack of segmentations does help a bit so, for the cost of another disk, I would say buy the slimmest width solid disk you can find to cut ceramic tiles with.
Date published: 2019-06-11
Rated 4 out of 5 by from Adequate but not perfect Used in my tile cutting machine. It does not make splinter free cuts, but the chipping of the glaze is no worse than the previous disk..... Applying masking tape and cuting through that helps minimise the chipping. In fairness I have yet to find a cutting disk that gets the job done chip free. In my humble opinion, for really clean chip free cuts, using a tile scorer and manually snapping the tiles still gives the best result for straight cuts.
Date published: 2019-06-11
Rated 5 out of 5 by from Great disc just right for the job Needed a disc to cut porcelain floor tiles. This disc did the job perfectly couldn't have completed the work without it
Date published: 2019-06-01
Rated 5 out of 5 by from Price factor in buying Cuts Porcelain tiles (8mm) with ease wet or dry. I have a 610x610x20mm Marble floor tile to cut into 3 pieces, should be a good test of this disc.
Date published: 2019-04-17
Rated 5 out of 5 by from great disk Great tool ideal for cutting ceramic tiles
Date published: 2019-04-12
Rated 5 out of 5 by from Good value blade I brought bthis to replace the original one in an electric tile cutter, it had done a lot of work and was well worn. Being a DIY'er I didn't want to buy an expensive one as it will only do a couple of tiling jobs, this blade worked well, cutting was easy, either wet or dry, there was also very little chipping of the ceramic surface which was good, I was using 600x250 and after about 150 it was still going strong. For a DIY'er tiling at home this is ideal, a professional would probably want a slightly better quality one for a longer life.
Date published: 2019-03-15
Rated 4 out of 5 by from good product i managed to cut 9mm tiles as long as you need to be bit gentle as it is a good cutter, you dont want to do over cutting, happy with the product overall
Date published: 2018-10-31
  • y_2019, m_12, d_6, h_12
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_1, tr_18
  • loc_en_GB, sid_56654, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_toolstation-gb
  • bvseo_sdk, p_sdk, 3.2.0
  • CLOUD, getContent, 82.17ms

You might also like

This site uses cookies to store information on your computer. Some of these cookies are essential to make the site work and others help us to improve services by giving us some insight into how the site is used. You can view our cookies policy here.