Premium quality, manufactured to BS1566 (part L compliant). 22mm primary heating coil. G1B preferred size of primary connections. Foam insulation factory applied to save time and money. 1" male screw connections for heating coil. 2.25" immersion heater boss, internal thread (female). Cold and hot draw off connections are both female.
||1045 IND BOX
Please note items delivered by our suppliers are not available for the options above.
Delivery times may vary.
More about Delivery & Returns
Click & Collect details
If you are using our Click & Collect service please note the following:
- Order online or over the phone and collect in branch from 10 minutes later.
- Ensure you check stock is available for collection at your chosen branch.
- Check branch opening hours to ensure you have sufficient time to collect.
- For items not available for same day collection, place order before 8pm Mon-Sat (4pm Sun) and you can collect Next Business Day (Mon-Fri) after 3pm.
- If we have your mobile number, we’ll send you a text when your order is ready to collect.
Indirect Hot Water Cylinder 1050 x 450 140L is rated
Rated 1 out of
Avoid at all cost
Needed new cylinder in a hurry and paid extra for next day am delivery- arrived by 11am next morning. Fitted with few issues, other comments re excess foam true but not a problem. Minor changes to pipework require but had hot water and heating by tea time.
Two days later woke to the sound of running water and found the kitchen ceiling sagging alarmingly with water dripping through it. All joints were still sound but there was a large pool of water behind the cylinder running through the floor around the emerging pipes.
Stripped cylinder out and refilled outside. Water dripping through foam and when I cut this away found the soldered seam between bottom and sides had failed.
Date published: 2019-05-05
Rated 1 out of
Lasted only 14 months before developing a leak. Manufacturer's warranty is 24 months but because it was over 12 months there was no assistance or cooperation from Toolstation. Still trying to get RM Cylinders to collect faulty cylinder and refund me.
Date published: 2019-03-01
Rated 4 out of
Needed a lot of foam trimming
The cylinder is good and the foam thick and quite tough.
The problem is the relief around the 5 ports was poor. Only the hot outlet was OK. Worst was the immersion heater port that was off centre and needed about 20mm cut away one side just to get a box spanner in. You need a box spanner for this cylinder. An offset spanner will not work. I must have spent a hour cutting foam back which I should not have to.
Date published: 2018-03-12
Rated 4 out of
In the process of fitting at the moment, tell you what its like when running. The test will be after a few years though
Date published: 2018-02-19
Rated 5 out of
Wanted a quick replacement for a tank with a weeping leak. Guess what, your favourite diy suppliers don't stock these anymore. Toolstation provided one next day from an on line order, delivered to my home, before middayin my case, at a competitive price. Terminal connections were compatible with the original fittings so no running out for new bits.
Terrific service, absolute lifesaver!
Date published: 2018-02-08
Rated 4 out of
Replacement for a 20+ year old cylinder.
Good value cylinder. The cold water feed and hot water outlet are 1" BSP, which caused me a dash to the plumber's merchants but the heating coil fittings were like for like. Used plenty of PTFE tape thanks to previous reviews, the tank felt a little flimsy when tightening joints but no leaks. Pretty happy.
Date published: 2017-11-10
Rated 2 out of
copper water tank
tank arrived with no bottom in the box
Date published: 2017-10-31
Rated 3 out of
Adequate, but not sure about quality and longevity
Arrived promptly and well packaged. Much thinner walls and heating coil inside much smaller diameter than old cylinder, so probably longer to heat water to required temperature. Label says it will take immersion heaters up to 1000mm long but my 880mm heater would not fit. Contacted manufacturer who said it would only take one up to 700mm and suggested I bought a 27" one. They knew label was wrong but it had been like that for some time and never changed. Indifferent attitude that basically said tough. Will have to wait and see if it lasts as long as old cylinder, which was 32 years, but somehow I doubt it.
Date published: 2017-10-26