Departments

Waterproof fibreglass mesh bonded with 180 grit silicone carbide grit on both sides. Can be used wet or dry. Suitable for deburring copper & metal pipe and cleaning inside fittings.

Comprises: 12" handle, 12" extension, 2"x6", 5/8"x6", 1"x2½" & 4"x1 7/8" nylon brushes, 3/4"x3" wire brush and 9/16"x2" phosphorus bronze brush.

Advanced formulation protects against scale, corrosion & bacterial growth in all types of indirect heating systems. 400ml treats 100 litres of system water. For use with Rapid Dose Tool Kit.

Tongue & groove non-slip jaws, with right angled teeth that grip in all directions for maximum bite. Comfort grips. Code 53474 and 85624 have 5 adjustments, 32mm jaw capacity. Code 83374 has 6 adjustments, 57mm jaw capacity.

Comprises 4 x 140mm & 5x120mm T handle, ball point hex keys. Fits most domestic pump heads.

Cuts 8, 10 and 12 O/D soft copper tubes. Anodized aluminium guide with 0, 30, 60, 90, 120, 150 and 180° markings. Steel handles with PVC grips.

For cutting plastic and vinyl pipes (6 - 50mm O/D). Safety clip for when not in use.
Body is manufactured from die cast aluminum and fitted with a hardened and tempered replaceable steel blade.

Prevents burn damage when soldering or brazing. Withstands high temperature flame and is Asbestos-free.

Cuts copper tube with only 3 turns

Waterproof and dirt resistant.

To position first fix pipes prior to screeding and plastering. Re-usable by unscrewing and lifting off once pipe is set. Multiple slots for 15mm OD pipe (which can be drilled to accommodate 22mm OD pipe), allows for accurate positioning for most radiator depths.

Suitable for non-locking covers and pedestrian duty broadsted.
Lifting capacity 30kgs

Enables hard to access valves to be reached and opens up infrequently used valves that are normally impossible to turn by hand.

For use on 15mm, 22mm and 28mm valves. Overall length 220mm.

Multi purpose key to suit 3/8", 1/2" & 3/4" square stop cock valves and crutch head valves. Pointed handle for opening stop cock covers.

Fits Tank connectors 15mm, 22mm & 28mm (internal & external lug), Tank connector with ½" internal hexagon, rad valves ½" internal hexagon (with or without internal lugs), ½" radiator air vent plugs, Radiator air vent (bleed) pin. Holds new sink and basin wastes whilst fitting.

Solid brass. Removes 15mm and 22mm olives without damage to pipes.

Speeds drain down of radiators, helps prevent unsightly stains on carpets and floors. Snap clip holds tub in position on 10, 15, 22mm pipe sizes. Angled fastener guides water to tub. Flexible construction allows tub to be compressed to fit under low hung radiators.

Slip and dirt resistant, wipe clean and machine washable (cool wash).
Water absorbent, quick drying lining. Pipe slots on two sides.

Chrome Vanadium with drop forged super slim wide jaws and a soft grip handle. Hardness and torque meets or exceeds ANSI spec B107.8M. 6" has 34mm jaw capacity, 8" has 38mm capacity, 10" has 50mm capacity and 12" has 60mm capacity.

Slim jaws. Quick action setting via push button selection. Twin-sided machine groove locking mechanism provides non-slip grip. Jaw capacity is 44mm.

Converts from standard adjustable wrench to ratchet wrench at the press of a button without removing the tool from its position. Jaw capacity is 32mm.

Versatile plastic key suitable for radiators, water, gas and electric boxes

Ideal for working in restricted areas such as boilers, motorised valves and closely aligned pipes. To use on 15/22mm copper pipes.

Clamps up to 25mm plastic pipe for effecting repairs without draining down the system or turning off the water supply

Removes stiff tap backnuts from ½" and 3/4" BSP taps.
Uses mechanical advantage of the thread of the tap tail to remove stiff nuts.
Enables rapid tap installation.
Use with tommy bar (not supplied) or cordless drill on lowest torque. Supplied with stickfast sticky washers and full instructions.

Multiple uses in plumbing & heating, particulary useful on plastic waste fittings. Jaw capacity 68mm, jaw depth 55mm.

Allows access to difficult to reach taps on bath and basins. Box spanner construction enables taps to be tightened or loosened in restricted apertures. Extension bars ease access to taps on baths. Split ring spanner design speeds tap connection assembly or disassembly.

Hardened and tempered milled jaws, six step adjustment and moulded handles with slip guards. 9.5" has 30mm jaw capacity, 11.5" has 65mm capacity and 15.5" has 110mm capacity.

Use for blocking off drain pipes. Fitted with removable top caps and rubber rings.

Use to tighten and loosen 15mm and 22mm compression fitting nuts.

Kit includes an expander tool, 15 & 22mm expander heads and a plastic bodied deburrer in a metal carry case.

For speedy assembly of most valve tails to radiators.

Zinc plated steel spanner with comfortable, slightly offset handle.
For 3/8" & 10mm square section radiator vent plugs & bleed screws

Allows system to be sealed by producing a vacuum, thus valves can be changed without draining the system.

Fits most brass and nylon back nuts.

Made from tough plastic. Marked in millibars, the scale adjusts to zero the water level. Cover slides off and may be clipped over the base for standing the tool vertically during use. Tab enables hanging from suitable protrusion. Supplied with standard black tube.

Zinc plated hexagon steel spanner with comfortable, slightly offset handle.

For joining two pieces of copper pipe of same diameter without using fittings. Resulting capillary joint can be soft or hard soldered. Loose socket former allows easier withdrawal of tool after use. Pipe wall thickness: 0.7mm (15mm) and 0.9mm (22mm).

Carbo-nitrided carbon steel cutting blades. Not suitable for removing stainless steel olives. 22mm will not fit 3/4" Imperial olives.

For cleaning the inside of copper fittings and socket formed joints on copper pipe prior to soldering. Stiff steel bristles.

For cleaning and deburring 15 and 22mm pipes.

High Tensile steel key for radiators.

Solid brass 'T' bar style.

Heavy duty all steel construction. Re-cuts worn tap seats. Hardened cutters sizes 3/4" & 1" included.

Handy mini tube cutter for 3-22mm copper tube. High speed steel cutting wheel & double rollers.

Cuts copper, brass, aluminium and light gauge steel.

For cutting copper, brass, aluminium, polyethylene & other light gauge pipes. Diameter range: 6-50mm. 2 spare cutting wheels. Built in deburring tool.

Copper pipe cutter. Not suitable for stainless steel.

Spring loaded self-adjusting cutting wheel cuts without having to make continuous adjustments.

ABS plastic pipe cutter. Die cast aluminium body & hardened steel blade. Ratchet & lever mechanism will cut pipe, conduit & plastic extrusions up to 42mm without crushing. Colour may vary.

Contains pipe clamp, 45° spreader & 7 dies 3/16", ¼", 5/16", 3/8", 7/16", ½", 5/8".

Tool for removing burrs from the ends of pipe. Hardened steel swivelling cutter head.

Heavy duty professional pipe bender for 15 & 22mm copper tube & 15mm stainless steel tube. Includes guides.

Use internally to prevent copper pipe from kinking when bending.

Forged steel handle with hardened jaws. 6.5" has 30mm jaw capacity, 13.5" has 70mm capacity and 23.5" has 60mm capacity.

Heavy duty forged steel wrench with hardened steel jaws. 70mm jaw capacity.

Self adjusting, laminated sheet metal construction. Enables one handed operation and comes with a comfort grip handle and steel jaws.

Drop forged 5 position adjustment with toothed jaws. Jaw capacity is 85mm. Complete with pair of removable soft jaws.

Heavy gauge steel box wrench with 'T' bar.

For most water, electric & gas cabinets.

Designed for easy removal of manhole covers. Made from a single piece of malleable iron with a tee handle and D shaped end.

Strong steel stop cock key. 1000mm long. Fits ½" crutch head stop cocks. Pointed handle for opening stop cock covers.

Strong cast steel. Fits 15 & 22mm back nuts & union nuts for most taps.

Makes reaching bath tap nuts & basin tap nuts easy. Adjustable pivoting head with hardened steel jaws. Fits ½" & 3/4" nuts.

Steel handle with hexagonal end and removable tommy bar. Fits 15mm and 22mm (½" and 3/4") nuts.

4 piece set includes 3 double ended box spanners and a tommy bar.
Sizes: 8, 9, 10, 11,12,13mm

Tough plastic central mandrel has inflatable replaceable collar secured by 2 clips. Central nipple for connection to U Gauge. Reverse end of plug has removable stopper for an air test. Replace stopper and use as a drain plug for blanking off pipes. Equipped with Schrader valve inflation hose. Maximum inflation pressure 12psi / 0.86 bar.

Suitable for threading black gas or galvanized iron pipes. Kit contains four die heads, two piece tubular steel handle and a compact ratchet head. Cast iron die heads with four alloy steel chasers per head for clean accurate thread cutting. Each die head has four swarf removal holes. Die sizes 1/2", 3/4", 1", and 1 1/4" BSP.

Measures in both Celsius and Fahrenheit and features a temperature hold function. Measuring range -50°C (-58F) to +125° C (+257F).